Wide outdoor steps leading to a house

Concrete Steps Calculator

Enter the height to climb and get the number of steps, the riser and going, a check against Australian stair limits, and the concrete to pour them.

1

Height and size

mm
m

Total rise is the height from the lower ground to the top surface (door threshold, deck or landing).

2

Step proportions

Target riser height
mm
m deep

Leave the landing at 0 if the steps finish at an existing slab, deck or doorway.

3

Concrete options

Extra for waste
Premix bag size
Quick answer: divide the total rise by about 175 mm to get the number of steps, keep each riser between 115 and 190 mm and each going between 240 and 355 mm, and multiply up the solid volume for the concrete.

How to work out the rise and going of steps

STEP 1Measure the total rise: lower ground to the top surface, in mm.
STEP 2Divide by a target riser (about 175 mm) and round to a whole number of steps.
STEP 3Divide the total rise by that number to get the exact riser for every step.

For a 600 mm rise, 600 ÷ 175 = 3.4. Three steps would give 200 mm risers, which is above the 190 mm limit, so use four steps of 150 mm. If the steps finish at an existing landing or doorway, there is one fewer tread than risers: four risers need three treads, so with a 280 mm going the steps run out 3 × 280 = 840 mm from the top.

Every riser in the flight should be the same height. A first or last step that is taller or shorter than the rest is one of the most common causes of trips.

What are the rules for steps in Australia?

For stairs in houses, the National Construction Code (ABCB Housing Provisions, Part 11.2) sets these limits for straight flights:

MeasurementMinimumMaximum
Riser (R)115 mm190 mm
Going (G)240 mm355 mm
Slope relationship (2R + G)550 mm700 mm
Risers in one flight218

Risers and goings must also be consistent within a flight, and openings between treads must not let a 125 mm sphere pass. Handrail and balustrade rules may also apply. Garden steps that are not part of a building may be treated differently, so confirm with your council or building certifier.

How much concrete do I need for steps?

Solid steps poured against the ground are a stack of blocks. Each tread sits on a block as deep as the going and as tall as its height above the bottom, so the first tread is one riser tall, the second is two risers tall, and so on. For a landing or path at the bottom, work out the extra volume with the concrete calculator, and check what a small load will cost with the concrete price per m³ calculator.

TREADSWidth × going × riser × (1 + 2 + … + number of treads).
LANDINGWidth × landing depth × total rise, if you're pouring one.
WASTEAdd 5–10% for uneven ground and spillage.

For four 150 mm risers, three 280 mm treads and a 1.2 m width: 1.2 × 0.28 × 0.15 × (1 + 2 + 3) = 0.30 m³. With 10% waste that is 0.33 m³, or about 36 bags of 20 kg premix. Steps cut into a slope use less, because the ground fills much of the space under each tread; measure the actual formwork in that case.

What size steps are comfortable?

Steeper

Risers near 185–190 mm and short goings save space but feel steep, especially going down.

Comfortable

Risers around 150–180 mm with goings around 280–300 mm suit most people.

Garden steps

Lower risers and deeper goings feel relaxed outdoors and on gentle slopes.

Before you pour concrete steps

  • Build the formwork with the riser boards set out exactly, and check each step with a level before pouring.
  • Give the treads a slight fall so water runs off, and use a broom or non-slip finish outdoors.
  • Steps against a house should not bridge the damp-proof course or cover weep holes.
  • Ask whether you need a handrail or balustrade, and whether the steps need approval.
Steps up to a doorway, deck or verandah? These are part of the building and need to meet the National Construction Code. Have them built or checked by a licensed builder or concreter.

Frequently asked questions

How many steps do I need?

Divide the total height you need to climb by the riser height you want, then round to a whole number. For a 600 mm rise with risers of about 175 mm, 600 ÷ 175 = 3.4. Three steps would make each riser 200 mm, which is too steep, so use four steps of 150 mm each.

What is the maximum step height in Australia?

For stairs in houses, the National Construction Code sets a riser height of 115–190 mm and a going of 240–355 mm, with twice the riser plus the going (2R + G) between 550 and 700 mm. All risers and goings in a flight must be consistent. Check the current edition with your building certifier, as other rules can apply.

How much concrete do I need for steps?

For solid steps poured against the ground, each tread sits on a block of concrete as tall as its height above the bottom. The calculator adds these blocks up: width × going × riser × (1 + 2 + … for each tread), plus any top landing. Four 150 mm risers with 280 mm goings and a 1.2 m width need about 0.3 m³, or roughly 36 bags of 20 kg premix with 10% waste.

What is a comfortable step height and depth?

Within the code limits, most people find risers of around 150–180 mm with goings of around 280–300 mm comfortable. Outdoor and garden steps are often made shallower and deeper than indoor stairs.

What does 2R + G mean?

It is the slope relationship used in the National Construction Code: twice the riser height plus the going. Keeping it between 550 and 700 mm matches the step to a natural walking stride, so the stairs are neither too steep nor awkwardly shallow.

Results are estimates to help you plan and compare quotes. They are not a substitute for advice from a licensed tradesperson or engineer.

Tiler pressing a wall tile into place

Steps up to a house or deck?

Get them quoted and checked by a licensed builder

Read the checklist